canadagoose
About
- Username
- canadagoose
- Joined
- Visits
- 115
- Last Active
- Roles
- Member
Comments
-
Thanks, I did that on the latest install. But I am Happy to report, I started a New flight and everything is smooth as butter all the way up to FL250. No hiccups with the AP disconnect, all systems seem a go now after the re-install. So, I'm happy t…
-
Thanks for that, before the video (which I do not know how to do) I will try a new flight, but just a note, I previously disabled these two lines in the mjc84.ini file: J0_b1=AFCS_->inputs.AP_disengage J0_b2=AFCS_->inputs.TCS_button I a…
-
I'm going to try Uninstalling and reinstalling again with Just Flight.
-
Just happened again. AP disconnect for no reason. Unfortunately, this is becoming an immersion killer, totally unflyable for me anyway. Possibly something was broken between the previous version and 1.024? When was the last version uploaded to Just …
-
Sorry I meant to say that my headphones are USB, and I use Pilot2ATC which goes through the Headphones. But I also get all of the aircraft sounds through the headphones as well. Just a note, I started the sim with the USB Headphones unplugged and th…
-
Thanks, I will look into that. So, can I just leave all Cpan settings on 3D. I've been doing trial and error. Just wondering what "Captain's & CoPilot's", "Headphones and Speakers" are used for on the Sound Map? Can I check all "Global & Dev…
-
I would think someone has possibly encountered and resolved an issue similar to this. Maybe not. Any help is appreciated. Regards
-
Everything is fine now, Support allowed me access to a different installer than the one at the Just Flight site and the installation went well! Thanks to Majestic Support for all their help!
-
It must be just me with this issue, very strange, no matter I have contacted "Support". Just curious though, what path did you point the Installer to? Certainly not the default one that pops up. I would think the path would be where the Q400 is inst…
-
@canadagoose said: @canadagoose said: @canadagoose said: I am slightly confused with the install location. I am getting a default location of : "C:\Program Files (x86)\Microsoft Games\Microsoft Flight Simu…
-
@canadagoose said: @canadagoose said: I am slightly confused with the install location. I am getting a default location of : "C:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X" That is not where P3Dv5 res…
-
@canadagoose said: I am slightly confused with the install location. I am getting a default location of : "C:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X" That is not where P3Dv5 resides. Can I PLEASE get a confirmation…
-
I am slightly confused with the install location. I am getting a default location of : "C:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X" That is not where P3Dv5 resides. Can I PLEASE get a confirmation on where I should be poin…
-
Forget it! All is well... My Mistake. I did not move the condition levers to 100%. That's why I couldn't move. Good thing about this post, it got me to using the cpan sensitivity setting app for my Yoke and Tiller. Thanks
-
A little more Info. Upon further testing I have found that I can recreate this issue with FFTF Dynamics IF, I close down P3D and restart P3D during The SAME session. BUT, if I shutdown the computer, go back in & create a flight using my normal …
-
Success! For myself anyway. I am now able to re-install the Q400. I also ran FFTF and everything appears back to normal. So, in my case the issue was just a simple download and re-install the aircraft. I will report back if I encounter any further i…
-
I am doing what I normally would do. Setup up the flight by choosing the “vehicle”, a DEP airport, set time and GO...the % load screen does not appear and after less than a minute, CTD. I have started using my Honeycomb “Alpha” yoke, that being the …
-
I am getting this same issue as well. But the aircraft is giving me a CTD with FFTF Dynamic not running as well. If it is not FFTF causing this then I am baffled because I have never had a CTD when running the Majestic Q400.
-
First of all I have to apologize for letting this post get out of hand. I have solved my own problem. As it has been a while since I used the Majestic Q400 I left out a very important step in the start procedure. All I had to do was turn on the APU …
-
If this installation file is the latest and it brings compatibility to P3Dv5.HF1 then I should not be having this problem. I am just taking stabs here, but is it possible this is a registration problem? I uninstalled through Windows before I re-inst…
-
Here's a screenie of![](http://majesticsoftware.com/forums/uploads/editor
-
...Actually I just tried a new state "Boarding"...still no luck. I tried CTRL+E and that is a No Go as well.
-
...I forgot to mention, as I always have I am using the "Default" Cockpit State if that is any help.
-
Now I got a message saying "default failures initiated". As stated above I have also changed the ini file item WearOffFactor????
-
...Also Red ENG 1 & 2 oil pressure warning. Is that the problem? I have also changed the ini file item WearOffFactor=0, so this cannot be a failure of some kind.
-
I have downloaded and installed the latest version which I assume is compatible with P3Dv5.1HF1 or NOT. I still can't get the engines to start. What am I doing wrong. I have never had this problem! Is there a patch coming? Am I missing something her…
-
Thanks for that, I checked my account over at Just Flight and the installer looks like it is the proper version even though it says it is for P3Dv4 (mjc8-400-Pro-1_021_x64-inst.exe). I ssume this is the latest installer. I installed it and I was giv…
-
My Just Flight Account says the product download link is for P3Dv4. Is this for P3Dv5 as well? That is the link I used to download and install the Pro version.