kroswynd
About
- Username
- kroswynd
- Joined
- Visits
- 6,360
- Last Active
- Roles
- Member, Administrator, Moderator
- Invited by
- Boss
Comments
-
That would be correct.
-
The variables provided by @Jax_in_BC are correct and can only be acquired with the list from the new installers. @Jax_in_BC... Thanks for offering your assistance
-
@aua668 - what Edition of the Q400 are you using? Pilot or PRO?
-
We'd like to be flying the Dash in the said platform but it will require quite a bit of back end work to get back on track. We will make announcements as usual via our forum and Facebook posts.
-
No there is not at this time, but we plan on bringing the 400 to the said platform.
-
The best thing to do to rule out a 3rd party addon is to run with out addons. We have done significant testing with Active Sky and we were able to rule it out as a contributing problem. I am have not used Aivlasoft in a while and do not have tim…
-
> @sarumlad said: > My crashes are not related to the time of flight. Just flown from EGPB sumburgh altitude 21ft to EGHI Southampton elevation 44ft 574nm and landed pertfectly with no problems at 1800ft when I interecepted the glide slope a…
-
> @dwadsworth said: > Yes, I had it on takeoff yesterday. I had just changed the AFCS_FSX_SYNC=0 in the ini file. Flying from CYVR on 08R YVR1 departure. After turning right to 215 to intercept YVR, I engaged the AP and shortly after tha…
-
* Pressing the AP button on the glareshield will not play the AP disconnect aural tone or provide an indication on the PFD. * Using the mouse to disengage the AP via the disconnect button on the yoke will play the disconnect aural tone and provid…
-
Thanks, so the syntax is correct. Just out of curiosity. can you swap the AP disengage with the TCS and see if you get any response from the TCS when engaged in flight plz. Do you use any 3rd party add-on that can any access to the AP functions.…
-
I tried to d/l your .ini again but it seems to be deleted
-
A. Make a backup of files that you may have made changes to (mjc84.ini, aircraft.cfg and liveries folders, etc.) - Uninstall the aircraft, then re-install and be sure to use Admin Rights. B. Write to our Support Department (support (at) majesti…
-
@micstatic ...Kindly hold off if you are intending to purchase the TRAINING edition as I was testing the TRAINING with the KSUN and noticed some oddities (it appears to be with this airport only though). It seems as though there may be some issue…
-
@Jax_in_BC thank you for pointing the issue out to @freddy. Easy to overlook, and did not consider asking him about it as this was a syntax that that is normally left on, unless it was disabled by @freddy when attempting to setup his controls. …
-
Copy, we are still looking into the issue. Thanks
-
The surface normals (surface angle) of the Prepar3D are integrated into the Q400 FDE, allowing for the correct visuals and physics when operating on addon runways with a slope That would be correct. This feature is only applicable to the TRAININ…
-
Thanks for the feedback, as we have not been able to replicate the issue using the flight plans provided. The NAVDATA that we supply with the installer is usually an older version provided wit the permission of Navigraph. Users can then determine …
-
I have tested this issue that you are experiencing and have not been able to replicate. Out of curiosity do you have bloom enabled?
-
No worries. So this specific issue after further review we were able to determine that are there isn't a fix applicable to the issue. I do realize the the answer does not satisfy the problem but P3D/FSX has had this underlying issue wher…
-
Hi Keith, If you choose to install over the existing installation then I recommend that you backup the liveries and the aircraft.cfg along with any other changes that you may have may to your mjc84.ini before proceedong with the installation. …
-
We have "disabled" the "z" key for autopilot disconnection within FSX/P3D as it has the capability of causing issues with the MJC AP (this was done since v1.009). If you use the "z" key we can not guarantee that the AP will work as it is intended v…
-
It really should not prevent the functionality as I have conducted one of the 3 flights that you provided without issue. If the issue happens again pause the sim, and save the scenario then zip the scenario files and attach them to this thread.…
-
Thank you for the info. When installing any addon for flight simulation it is recommended that one temporarily disable and firewall/anti virus application before commencing download and or installation.
-
@Sergio, thanks for your input but this has been a discussion in existence for almost 4 years. Everyone is aware of the operation of the gear pin functionality. The discussion piece is more about the issue and possible causes of the issue since…
-
This has been one of the more challenging bugs to replicate and find a definite cause. While have speculated a few possible causes but the back end work to address this if it is the cause is will be time consuming. We try to collect as much in…
-
Unfortunately some vendors tend to produce the installers quicker than others. Hopefully we hope that this will be up for all vendors by the weekend.
-
We would not omit this function with it being a rudimentary aspect of the devices operation during that phase of flight. Do you have a particular route that we can test to verify?
-
There should be as all vendors were sent new installers
-
These will pose a conflict if the controller that is assigned at J0 with those buttons are assigned to different functions via your joystick binding process in P3D or fsuipc. Simply disable them by putting a ";" in front of the syntax, especial…
-
There has not been an update, but more so new installers sent to vendors. Have you installed the new installer of which you advised that you are have these issues. Providing a video of the issue would be better for us to understand exactly w…