vrouleau

About

Username
vrouleau
Joined
Visits
71
Last Active
Roles
Member

Comments

  • Are are sure you dont have the "Immersion Manager" issue. Did you stop //42 Immersion Manager when running the Q400?
    in Screen/Scenery Bouncing in v5.1 Comment by vrouleau November 2020
  • FYI, I had the exact same problem. Close IM indeed fixed it
    in Bouncing and error with panel state Comment by vrouleau September 2020
  • Is there a solution for this? FYI Found it. 2 days ago I updated the G633 software. Logitech installed a component "Logitech G-Hub". That was causing my problems. I uninstalled it and the sound works after reverting to 3D in CPAN
    in Sound Issue Comment by vrouleau September 2020
  • It started happening to me yesterday. I've been flying the Q400 frequently for the past few weeks. Yesterday, all of a sudden on my Logitech G633, I loose engine noise from the cabin when I look in front. If I turned my head, the sound would come ba…
    in Sound Issue Comment by vrouleau September 2020
  • Fyi, I also got it once and on win10 2004 using queued timer. The alt were the same and was on sync on in the ini
    in "Alt Disagree" Comment by vrouleau June 2020
  • I've set the time to "MULTIMEDIA TIMER" and did 2 tests KRND and CYUL and Fuel flow and fuel remaing delta calculations now match. So I will leave that setting on my system. This is the first I was monitoring my fuel remaining so closly because…
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • Sorry for the late reply 1) yes, I have updated to windows10 2004. Nvidia 450.99, P3DV5 HF1 2) Timing source : Queue Timer
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • Regardless of load out or what Simbrief and calculated, the actual fuel burned as reported by the software does not match the fuel flow used during the reported period of time. My question remains: why is there a 2x factor ( 1000 vs 500 ) different …
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • Hi, In the example I provided in the screenshot above, I provide a the simplest scenario that I could. I ran over the course of only 20 minutes. 1)I lifted off from CYUL and flew to FL150 heading 63 degrees and stabilized at 236 knots clear da…
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • Take of CYUL 6L, going strait 63o
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • Did another test with plane configured in LBS. Same conditions, 0 Winds/Clear sky , 236Kts /FL150 Reported FF: 2213 Mesured FF on fuel remaining: 1092
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • Here a test. No Wind/ clear skyies. Screen shots at 10 min intervals. Speed/alt constant 236 kts/FL150 Reported FF 1005kgs/h. Mesured FF on fuel remaining 514 kgs/h
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • I had avg 20kt headwind component during the flight. I figured 1100kgs is impossible. I’ll wait for official release. Thanks
    in Fuel flow on p3dv5 Comment by vrouleau June 2020
  • I still use it. It works in P3DV5. See thread: http://majesticsoftware.com/forums/discussion/245/v-speed-calculator-and-setter-xml-gauge
    in Majestic Q400 V-speed calculator and setter Comment by vrouleau June 2020
  • Edit: Never mind. I put in incorrect values in the panel.cfg. Its works perfectly now Has anybody tried the Vspeed calculation panel? I tried to install it but the aspect ratio is all wrong http://majesticsoftware.com/forums/discussion/245/v-sp…
    in P3D v5 compatibily? Comment by vrouleau May 2020