aua668
About
- Username
- aua668
- Joined
- Visits
- 2,392
- Last Active
- Roles
- Member
Comments
-
To start to count with zero is the more logical way in terms of programming. Maybe the sim is not following the standard You should ask LM, why they started with one instead of zero. Rgds Reinhard
-
Hi, The documentation "SpecialFeatures.pdf" page 4 is very clear: B is 0 based joystick button sequential number, from 0 to 127 Rgds Reinhard
-
It depends, how you count. Starting wit zero (=offset from the first button) or with one (first button). You have to choose one starting point. Obviously here counting starts with zero. Therefore b2 is the third button. It's not so complicated …
-
Hi, I switched HT on and off several times for testing different performance setup scenarios, and this was no issue at all for the Q400 and the license. Rgds Reinhard
-
Hi, Thanks - now it's cĺear. It's a little bit misleading, that there are controls in the interface, and that they light up, if you turn them on using the mouse. Best regards Reinhard
-
Hi, Wilco. As this always happens immediately at the start, it's easy to check. I will save the scenario in such a case and I will send the ZIP to the support. There might be some time, until it happens again. Rgds Reinhard
-
Hi, After a long period without any problem, I experienced th altitude differenc again. departing from LOWI to LGKR the primary altimeter showed a height, which was 200 ft too low. The secondary altimeter was correct. Changing the QNH on the prim…
-
Hi, Maybe this thread helps you to implement the hardware mapping: majesticsoftware.com/forums/discussion/1098/assigning-buttons-via-fsuipc-directly-to-xml-interface-controls#latest But be aware: You must understand the XML interface and mu…
-
If you experience frame rate problems, it's not the Q400. It's P3D 5.2. There is a thread on the AVSIM forum, dealing with the increased load on LP0 of the CPU. Affinity mask helps in case you are using Hyperthreading. But it's definitely not the Q4…
-
Hi, Are you using any shader mods (Envshade or similar)? Rgds Reinhard
-
https://letmegooglethat.com/?q=Q400+Majestic+SPLR+OUTBD+QRH
-
Hi, https://smartcockpit.com/docs/Q400-Indicating_and_Recording_Systems.pdf Page 136. Rgds Reinhard
-
Hi, Are you using the Immersion Manager for the Q400? majesticsoftware.com/forums/discussion/comment/3846#Comment_3846 Rgds Reinhard
-
Hi, Have you seen this thread: majesticsoftware.com/forums/discussion/1076/hgs-cat-iii-equipements Rgds Reinhard
-
For mapping the YD button you have to use the XML interface as described in the documentation provided. You must use the AFCS mode button with parameter 12. Rgds Reinhard PS: If you don't know about the XML interface and you are not a pro…
-
FYI: The only drawback of mouse macros is, that with every new version of the Q400 you have to recreate them, as they point directly into the gauge code via hex addresses. But as there are only few buttons and the number of new releases is not so dr…
-
Hi, I have the GF MCP Pro running with the Q400. I used LUA programs via FSUIPC using the XML interface. As it is part of a complete installation, sharing of the programs wouldn't help you. I would also suggest to look for LINDA, if they have …
-
Have you controlled the brakes working in the control panel ? Have you calibrated them there? Rgds Reinhard
-
Hi, If you are aware about LUA in FSUIPC and the XML interface of the Q400 you are able to assign a joystick button to the TOGA button. Maybe you check the documentation for these items. Rgds Reinhard
-
Hi, The three types of climb are often referenced by the following names: * Type I (high speed) * Type II (intermediate speed) * Type III (low speed) Rgds Reinhard
-
Hi, Which climb mode did you select? Pitch Hold, VS, IAS? Only pressing ALT SEL does nothing but leveling off if you reach the selected altitude. Rgds Reinhard
-
Hi, In the scriptLib directory of the Q400 you find the settings for the several scenarios. The File ccColdAndDark.mgs sets the parameters. You might try to set the variable #electricsData_->gpuRequested in the Electrics section to zero. I hav…
-
Have you also checked the 125Hz section in the INI file? There might be a wrong setting per default. Egds Reinhard
-
@helico55 said: Each time I must to arm myself. And where is the problem? You do other things too, if you arm the approach as described in detail in this thread. Rgds Reinhard
-
Hi, Another question: Have you tried this with different send rates, which are controlled by that line in the INI file: SEND_RATE_DIVIDER=8; // 16 times per second Try to lower the rate and check, if this makes a difference. Rgds Reinha…
-
Hi, This might be a similar effect, which I am seeing with AviaServer for the Q400: majesticsoftware.com/forums/discussion/1009/udp-packet-transmission-for-aviacdu-stops-sometimes-during-cdu-initialization I have the feeling, that something…
-
Hi, An update: I switched back from the broadcast mask 127.0.0.1 to the mask for my LAN (192.168.1.255) and the error did happen again. I had problems to recive packets with the AviaServer at the beginning of my flight, which did go away after ar…
-
Hi, One update for your information: I changed for testing purposes my broadcast IP to the localhost address 127.0.0.1 and I am not broadcasting by that into my LAN. Since that change I could not reproduce the error. There was one update of the A…
-
Hi Boss, Good to know. I will try your suggestion, at the next occurrence of this failure. The last flights have all been ok. That's the bad thing with failures, which only happen from time to time. They are hard to reproduce and therefore the ni…
-
Hi JP, It's definitely perfect for handling this plane, if it works. I use it also for the Aerosoft A320. One of the first things to configure is of course the INI file and the UDP interface configuration. Next is the firewall as well on the PC a…