aua668
About
- Username
- aua668
- Joined
- Visits
- 2,213
- Last Active
- Roles
- Member
Comments
-
Hi, I just checked it again: "EFISdata_->STBY_QNH" has the code 15433. So obviously you can write to this control too. The baro rotary knobs and the STD buttons are controlled by these variables: airData_->ADC[0].controls.barometricCo…
-
Hi, I set the STBY QNH via control 15433. I can't remember, where I did find this code, but via thisXML code I am able to write the QNH directly. STD I use the same control with 1013.2 as the parameter. Rgds Reinhard
-
Hi, With these two screenshots alone it's not possible to reproduce and analyze the problem. So please provide: * The route you are entering * A screenshot of all FPL pages of the CPT CDU and the FO CDU after x-filling it on the FO side * …
-
Hi, Craig - you are right: I am using 125Hz control and by that have these entries set to 0. I used always the turbulence factor 0.75 together with ASP3D and have never touched it. In ASP3D I have turned of the enhanced turbulence, which is the d…
-
Hi, Another question: Are you using two yokes for controlling the plane? If not, you should follow the hint in the special features guide: Important: Should both left and right flight columns be controlled via a single joystick (no split contr…
-
Hi, Looking at your INI file, you obviously have calibrated the engine controls via the control panel. But the flight controls look unconfigured. Have you configured and calibrated them by the simulator or by the control panel? In the flight c…
-
Hi, Some more questions: How have you configured your flight controls? 125Hz, FSUIPC, directly with the simulator? Could you provide a copy of your INI file? Are you using a special weather program? Which simulator version are you using and which…
-
Warwick, Could you provide some screenshots or a video of your approach. I really fly a lot with this plane, but I do not experience your problems. I assume, you have calibrated your throttles accordingly, so that you are really at idle. Which ty…
-
Hi, I think you are looking for these controls: EFISdata_->ARCDUs[0].cntrl_mode EFISdata_->ARCDUs[0].cntrl_sidekey_input EFISdata_->ARCDUs[0].cntrl_tune_small EFISdata_->ARCDUs[0].cntrl_tune_large EFISdata_->ARCDUs[1].cntrl_…
-
Hi, I was asking for the AIRAC because of the magnetic variation. If charts, scenery and FMS data are not matching in terms of time, you might experience deviations, as the variation is changing over time. Details about this topic and how it's ha…
-
Hi, I assume, you mixed up IAS (indicated airspeed) and TAS (true airspeed). Don't know, what your reference in Wikipedia was. But the Q400 is showing IAS. The difference btween IAS and TAS you also find explained in Wikipedia. Rgds Reinhard
-
Hi, Are you using the default scenry or any addon? Which AIRAC are you using? Rgds Reinhard
-
@SABAV8R said: I find the ILS precision to be very undesirable close to the field. I am often way off track, outside of the runway boundaries. Also, the glideslope is erratic too. Hi, Be aware, that a lot of ILS are not aligned complet…
-
Hi, Great support from Majestic as always! I received the following mail: support@majesticsoftware.com Mi, 29.09.2021 19:23 Hello Reinhard Thank you for your message You could use CautionWarning_->outs_.master_caution_light …
-
@fscenes said: Aloha Folks, Looking to see if anyone is able to get at speed outputs, flashing types, ie; caution, warning, ap disconnect, etc. I have managed to get all my inputs and outputs on my glareshield and AP work under the xml for…
-
@kroswynd said: Good info gents, be sure to drop a line with this query to our support department, and I will add it to our items for review in our bug tracker. Done! Reinhard
-
Hi, That's my experience too. The blinking outputs are hard to catch via XML interface. It would be better, if they would send a continues ON while they are active. The blinking then could be implemented on hardware side. Rgds Reinhard
-
To start to count with zero is the more logical way in terms of programming. Maybe the sim is not following the standard You should ask LM, why they started with one instead of zero. Rgds Reinhard
-
Hi, The documentation "SpecialFeatures.pdf" page 4 is very clear: B is 0 based joystick button sequential number, from 0 to 127 Rgds Reinhard
-
It depends, how you count. Starting wit zero (=offset from the first button) or with one (first button). You have to choose one starting point. Obviously here counting starts with zero. Therefore b2 is the third button. It's not so complicated …
-
Hi, I switched HT on and off several times for testing different performance setup scenarios, and this was no issue at all for the Q400 and the license. Rgds Reinhard
-
Hi, Thanks - now it's cĺear. It's a little bit misleading, that there are controls in the interface, and that they light up, if you turn them on using the mouse. Best regards Reinhard
-
Hi, Wilco. As this always happens immediately at the start, it's easy to check. I will save the scenario in such a case and I will send the ZIP to the support. There might be some time, until it happens again. Rgds Reinhard
-
Hi, After a long period without any problem, I experienced th altitude differenc again. departing from LOWI to LGKR the primary altimeter showed a height, which was 200 ft too low. The secondary altimeter was correct. Changing the QNH on the prim…
-
Hi, Maybe this thread helps you to implement the hardware mapping: majesticsoftware.com/forums/discussion/1098/assigning-buttons-via-fsuipc-directly-to-xml-interface-controls#latest But be aware: You must understand the XML interface and mu…
-
If you experience frame rate problems, it's not the Q400. It's P3D 5.2. There is a thread on the AVSIM forum, dealing with the increased load on LP0 of the CPU. Affinity mask helps in case you are using Hyperthreading. But it's definitely not the Q4…
-
Hi, Are you using any shader mods (Envshade or similar)? Rgds Reinhard
-
https://letmegooglethat.com/?q=Q400+Majestic+SPLR+OUTBD+QRH
-
Hi, https://smartcockpit.com/docs/Q400-Indicating_and_Recording_Systems.pdf Page 136. Rgds Reinhard
-
Hi, Are you using the Immersion Manager for the Q400? majesticsoftware.com/forums/discussion/comment/3846#Comment_3846 Rgds Reinhard